SONOFF Wi-Fi BasicR3 Switch Actuator

Product Information

Unfortunately, this is not over. When Sonoff R3 is powered on while the jumper is installed, it will try to connect to the following WiFi credentials: SSID: sonoffDiy The new version of the Sonoff Basic smart switch uses an ESP8285 SoC with the 1MB flash integrated into the same SoC chip.

Long press the button for 5 seconds to enter pairing mode, then press another 5 seconds to ender Compatible Pairing Mode (AP). The LED indicator should blink continuously. Based on the classic BASIC, SONOFF constantly extends the product category, as well as improves and optimize product performance in sequence. Ultimately, BASICR2 with ETL certification comes out. User tips: If the device has been paired with eWeLink APP, reset the device is necessary by long pressing the pairing button for 5 seconds to enter Bluetooth Pairing Mode.

MANUALS

Usable GPIO: - GPIO14 is broken out on the PCB adjacent to the GND pin. - GPIO13 - You must remove the bi-colour LED - GPIO04 - You must solder wire to pin on ESP chip Official Sources ~

Ghi chú: Sonoff Basic R3 không có module thu sóng 433 MHz. Tuy nhiên, nếu bạn có nhu cầu thì có thể xem xét sử dụng Sonoff RFR3 - một phiên bản tương ứng với Basic R3 nhưng có thêm tính năng điều khiển qua sóng vô tuyến RF 433.The button is still very fragile, so take extra care during assembly and disassembly. Sonoff Basic R3 WiFi To flash new firmware, use URL: http://192.168.1.12:8081/zeroconfig/ota_flash and push the correct firmware details: {"deviceid":"10008fxxx", September 25th, 2021, Update #1: Updated the curl commands to escape double quotation marks ( ") in the -d (HTTP POST data) argument. I also made other minor changes to improve command execution (e.g., setting up environmental variables for IP_SONOFF and IP_HOST), fix typos, and improve readability. To turn the Sonoff R3 on/off simply submit the correct value to the URL: http://192.168.1.12:8081/zeroconfig/switch {"deviceid":"10008xxxx", The connectivity module is identical with Sonoff Basic R3. It uses ESP8582 to communicate with the Internet and the same pins are exposed for you to use: Vcc, GND, TX, RX – These are the standard GPIO pins.

Sep/2021:12:51:30 -0300] "GET /tasmota-lite.bin?deviceid=10011b78f7&ts=1576460931&sign=c2029fdd9d52ed2272c085ba79ffd5a88f11e94c8385f41bb68630de3c7b39b5 HTTP/1.1" 206 4399 "-" "itead-device" Along with support for smart scenes, just set a device to turn on/off to make another or a boatload of devices turn on/off. The LAN control is designed for situations which no available Wi-Fi connection, or an unsteady Wi-Fi network environment. A convenient option that is share control is capable of allowing you to manage the same device with your family or friends together, simply share it on the eWeLink app to try. I’m not sure why such a convoluted way to something so simple, but I decided to roll with it. I changed the WiFi credentials and I could use this cumbersome tool to toggle the status ON and OFF. It was time to see if I can issue commands.

 Product Documents

The operation failed and the request was formatted incorrectly. The request body is not a valid JSON format.

The operation failed and the device does not exist. The device does not support the requested deviceid. ITEAD’s Sonoff Basic R3 has expanded. Apart from the WiFi version that we all know and like, there is an RF (433 MHz) and Zigbee. Since the hardware had changed as well I thought I would take each Sonoff Basic R3 apart and poke inside the modular design. Sonoff Basic R3 series Inching emulates a “long press of a push-button”. This will enable the relay for a short time then automatically turn the relay off. To use the setting you have to enable it and provide the pulse duration in ms (and increments of 500) in the range of 500 – 36 000 000. (0.5 sec – 10h). Submit the values to URL: http://192.168.1.12:8081/zeroconfig/pulse {"deviceid":"10008fxxx","data":{"pulse":"on","pulseWidth":2000}} The exposed pins come with the 2.54mm pitch and you can solder the standard Raspberry Pi header. The number of pins varies between 4 and 5.data1={“switches”:[{“switch”:”on”,”outlet”:0},{“switch”:”off”,”outlet”:1},{“switch”:”off”,”outlet”:2},{“switch”:”off”,”outlet”:3}],”sledOnline”:”on”}